technical data sheet 7-16 airline plug / jack 60S101-K150 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 1 / 3 rf_35/09.14/6.2 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg all dimensions are in mm; tolerances according to i so 2768 m-h interface according to iec 61169-4, en 122190, din 47223 documents application note an001 calibration services material and plating connector parts material plating center conductor plug side brass gold, min. 1.27 m , over nickel center conductor plug side cube gold, min. 1.27 m, over nickel outer conductor brass gold, min. 1.27 m, over nick el coupling nut stainless steel passivated gasket nbr
technical data sheet 7-16 airline plug / jack 60S101-K150 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 2 / 3 rf_35/09.14/6.2 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg electrical data insertion loss 0.09 db at 8 ghz mechanical data mating cycles 500 maximum torque 35 nm recommended torque 2.26 nm airline dimensions at 23 c: - diameter outer conductor 16.060 mm 0.010 mm - diameter inner conductor 6.975 mm 0.005 mm - length outer conductor 150.00 mm + 0.02 mm - length inner conductor 149.98 mm - 0.02 mm - length difference 0.06 mm (outer conductor C inner conductor) calculated data (non warranted) lossless characteristic impedance 1 50 ? 0.10 ? return loss 2 45 db, 0.2 ghz to 4 ghz 40 db, 4 ghz to 8 ghz 1. the lossless characteristic impedance is calcula ted from the specified diameters of the inner and o uter conductor. 2. the return loss is calculated from the character istic impedance, the skin depth and the connector i nterface. general standard definitions for proper work the vector network analyzer (vna) u sed needs a model describing the electrical behavio ur of this calibration standard. depending on the vna type different models, units and terms are used and have to be entered into the vna. all values are based on typical geometry and plating. - offset z o / impedance / z o 50 ? - offset delay 502.542 ps - length (electrical) / offset length 150.059 mm - offset loss 0.60 g ? /s - loss 0.0261 db/ ghz environmental data operating temperature range 3 +20 c to +26 c storage temperature range 0 c to +50 c rohs compliant 3. this range is a recommendation. however, the air line can be used in a wider range. any temperature change from 23 c results in dimen sional changes.
technical data sheet 7-16 airline plug / jack 60S101-K150 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 3 / 3 rf_35/09.14/6.2 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg declaration of calibration options factory calibration standard delivery for this calibration standard inc ludes a factory calibration. the calibration certif icate issued reports individual mechanical calibration re sults, traceable to national / international standa rds. model based standard definitions are reported in an agilent/keysight, rohde & schwarz and anritsu compatible vna format. accredited calibration not available. for further, more detailed information see applicat ion note an001 on the rosenberger homepage. calibration interval recommendation 12 months packing standard 1 pce in box weight 420.9 g/pce center conductor loose in an acrylic glass tube draft date approved date rev. engineering change n umber name date herbert babinger 14.03.05 martin moder 09.11.15 f0 0 14-1492 maik knoll 09.11.15 while the information has been carefully compiled t o the best of our knowledge, nothing is intended as representation or warr anty on our part and no statement herein shall be construed as recommendation to infringe existing patents. in the effort to improve our products, we reserve the right to make changes judg ed to be necessary.
|
